Différences entre versions de « Projets:Finger Starter »

De wikilab
Ligne 37 : Ligne 37 :
 
[http://inmoov.fr/finger-starter/ finger starter]
 
[http://inmoov.fr/finger-starter/ finger starter]
  
 +
Détail des capteurs : [https://images-eu.ssl-images-amazon.com/images/I/C1lrpIfADaS.pdf Détail des capteurs]
  
 
==Image des différentes versions réalisée avec le code correspondant==
 
==Image des différentes versions réalisée avec le code correspondant==

Version du 26 mars 2021 à 14:18

Description du projet

Le projet est de réaliser un finger starter proposé par Inmoov : finger starter

Cahier des charges

Utiliser un kit de capteurs afin de contrôler le finger starter de manière originale.

Analyse de l'existant

http://inmoov.fr/finger-starter/

Equipe (Porteur de projet et contributeurs)

  • Concepteurs/contributeurs : Alix
  • Fabmanager référent : Yo
  • Responsable de documentation : Yo

Matériel nécessaire


Outils nécessaires

  • Un ordinateur

Coût

  • - de 50€

Fichiers source

finger starter

Détail des capteurs : Détail des capteurs

Image des différentes versions réalisée avec le code correspondant

  • 1 - Boutton
#include <Servo.h>

Servo myservo;                      // create servo object to control a servo

const int servoPin = 9;             // Digital PWM pin used to control the servo
const int buttonPin = 8;            // Digital pin to attach the button

int val = 0;                        // variable to read the value from the button

void setup() {
  myservo.attach(servoPin);         // attaches the servo to "servoPin"
}

void loop() {
  val = digitalRead(buttonPin);     // gets button current state 
  if (val == 0) {                   // checks if the button is pressed
    myservo.write(120);             // lifts finger
  }
  else {
    myservo.write(10);              // lowers finger
  }
  delay(30);                        // waits for servo to get there
}
  • 2 - Photo-interrupteur
#include <Servo.h>

Servo myservo;                      // create servo object to control a servo

const int servoPin = 9;             // Digital PWM used to control the servo
const int photoPin = 8;             // Digital pin used to control the photo interruptor

int val = 0;                        // variable to read the value from the photo interruptor

void setup() {
  myservo.attach(servoPin);         // attaches the servo to "servoPin"
}

void loop() {
  val = digitalRead(photoPin);      // reads value from photo interruptor 
  if (val == 1) {                   // check if the photo interruptor is blocked
    myservo.write(120);             // lifts finger
  }
  else {
    myservo.write(10);              // lowers finger
  }
  delay(30);                        // waits for servo to get there
}
  • 3 - Photorésistance
#include <Servo.h>

Servo myservo;                            // create servo object to control a servo

const int photoResistPin = A0;            // Analog pin used to connect the photo resistor 
const int servoPin = 9;                   // Digital PWM used to control the servo

int light = 0;                            // variable to read the value from the photo resistor pin

void setup() {
  myservo.attach(servoPin);               // attaches the servo to "servoPin"
  pinMode(photoResistPin, INPUT);         // puts the photo-resistor pin in INPUT
}

void loop() {
  light = analogRead(A0);                 // reads value from photo-resistor
  light = map(light, 0, 1023, 180, 0);    // scales it to be usable by the servo
  myservo.write(light);                   // sets the servo position according to the value
  delay(30);                              // waits for the servo to get there
}